WORK SHEET -
427SC
Please print this out and fax to us for confirmation (860)827-1055
| Qt. | Price | Total | ||
| Basic Turnkey | Without engine, transmission and wheels, metalic paint w/o stripe, Stewart Warner gages, vinyl interior, standard suspension with anti-sway bars, GM brakes front, Jag brakes rear, with 4 double adjustable dampers. Steel side pipes with VHT paint. Standard radial tires. | 1 | $37,900 | |
| Engines | 428 with about 400 bhp, aluminum heads, w/ clutch, bell housing, expansion tank, alternator, starter, etc | $9500 | ||
| 427 Side oiler - about 450 bhp, aluminum heads, as above, $16,000 to $30,000 | ||||
| 390 with about 375 bhp, iron heads, as above | $7000 | |||
| 302-351 as above --------- $4000-$12,000 | ||||
| Other engines on request | ||||
| Transmissions (All prices include linkage and handle) |
4 speed Top-loader, wide ratio, w/linkage and handle | $1350 | ||
| 4 speed Top-loader, close ratio, w/linkage and handle | $1550 | |||
| 5 speed Richmond Gear, w/linkage and handle | $2450 | |||
| 5 speed Tremec TKO, w/linkage and handle | $1700 | |||
| Rear suspension | Complete, ERA design, with outboard brakes, installed. Add | $800 |
||
| Wheels | 15" Bolt-on (Team III) | $1200 | ||
| 15" Pin drive, aluminum (original 6 pin style) | $4000 | |||
| 15" Pin drive, aluminum (5 pin w/adapters) | $2800 | |||
| 17" Pin drive, aluminum (6 pin) | $4500 | |||
| Brakes(optional) | Front: 12.2" rotors with Sierra 4 piston calipers | $1200 | ||
| Rear: 10.5" vented rotors, Girling calipers (Jag rear only) | $750 | |||
| Paint/Body | Stripe | $500 | ||
| 3 part metallic ------- $500-$1500 | ||||
| Hood scoop-----Rivited on | $50 | |||
| ------------------Molded in | $150 | |||
| Chip guard for rear fenders | $100 | |||
| Rectangular tail lights/twist-off front lights | $200 | |||
| Nudge bar-----front | $185 | |||
| ----------------rear | $185 |
|||
| Interior | Leather seats, shift boot, door pockets | $600 |
||
| Wilton Carpeting | $600 |
|||
| Heater/defroster | $390 |
|||
| Seat belts, shoulder harnesses, custom racing (two sets) | $250 |
|||
| Custom fluted dash knobs | $60 |
|||
| Gages(optional) | Smiths with clockwise speedometer | $400 |
||
| Smiths with ccw speedometer | $600 |
|||
| Roll bar(optional) | Powder coated black | $375 |
||
| Chromed | $500 |
|||
| Exhaust system | Undercar exhaust w/ ceramic coated primary pipes | $400 |
||
| Ceramic coat standard steel side pipes ------- Black | $350 |
|||
| -----------Silver | $300 |
|||
| -----------White | $350 |
|||
| Ceramic coat standard steel primary pipes | $200 |
|||
| Stainless steel side pipes, polished | $1100 | |||
| Heat shields and extra venting for cooling primary pipes | $150 |
|||
| Oil cooler(optional) | 4" Cooler with on-block oil filter | $400 |
||
| With remote oil filter | $650 |
|||
| Add for 6" cooler and special shrouding | $100 |
|||
| Cooling fan extra large |
H.D. 1800 cfm | $250 |
||
| Dual front fans (supplement rear fan) | $350 |
|||
| Top, installed | Vinyl | $1500 | ||
| Side curtains | Installed | $900 |
||
| Tonneau Cover | Fit to car, in vinyl | $180 |
||
| Aluminum inner fender covers | Anodized | $950 |
||
| Shipping | Approximately! Florida: $600, Texas: $1000, California: $1500 | |||
TOTAL: |
All prices are subject to confirmation. I try to keep up with changes, but sometimes...